Load "d:\\Project\\ÈμҺÀ\\20230731_XiaMenShiCheng_emb\\ZTMS_XiaMenShiCheng\\Project\\MDK\\Objects\\xiamenshicheng.axf" 
Set JLink Project File to "d:\Project\ÈμҺÀ\20230731_XiaMenShiCheng_emb\ZTMS_XiaMenShiCheng\Project\MDK\JLinkSettings.ini"* JLink Info: Device "TM4C1292NCPDT" selected.

JLink info:
------------
DLL: V6.56a, compiled Nov 25 2019 17:05:33
Firmware: J-Link V11 compiled Nov  8 2019 16:44:29
Hardware: V11.00
S/N : 50120677 
Feature(s) : GDB, JFlash, FlashDL, RDI, FlashBP 

* JLink Info: TotalIRLen = 4, IRPrint = 0x01
* JLink Info: JTAG chain detection found 1 devices:
* JLink Info:  #0 Id: 0x4BA00477, IRLen: 04, CoreSight JTAG-DP
* JLink Info: Scanning AP map to find all available APs
* JLink Info: AP[0]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[1]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[2]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[3]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[4]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[5]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[6]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[7]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[8]: AHB-AP (IDR: 0x24770011)
* JLink Info: AP[9]: AHB-AP (IDR: 0x24770011)
* JLink Info: Iterating through AP map to find AHB-AP to use
* JLink Info: AP[0]: Core found
* JLink Info: AP[0]: AHB-AP ROM base: 0xE00FF000
* JLink Info: CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
* JLink Info: Found Cortex-M4 r0p1, Little endian.
* JLink Info: FPUnit: 6 code (BP) slots and 2 literal slots
* JLink Info: CoreSight components:
* JLink Info: ROMTbl[0] @ E00FF000
* JLink Info: ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
* JLink Info: ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
* JLink Info: ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
* JLink Info: ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
* JLink Info: ROMTbl[0][4]: E0040000, CID: B105900D, PID: 000BB9A1 TPIU
* JLink Info: ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
ROMTableAddr = 0xE00FF000
* JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
* JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.

Target info:
------------
Device: TM4C1292NCPDT
VTarget = 3.232V
State of Pins: TCK: 1, TDI: 1, TDO: 1, TMS: 0, TRES: 1, TRST: 1
Hardware-Breakpoints: 6
Software-Breakpoints: 8192
Watchpoints:          4
JTAG speed: 5000 kHz

Erase Done.Programming Done.Verify OK.* JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
* JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.
Application running ...
Flash Load finished at 11:25:19